联系Z6尊龙官方网站官网入口
Z6尊龙官方网站官网入口
联系人：林经理
电话：151 6888 2846
邮箱：527800164@qq.com
地点：济南市历下区化纤厂路8号3号楼101号
工业卷帘门的轨道装置需要注意什么?
工业卷帘门的轨道装置需要注意什么呢?轨道是工业门开关运行的主要部件 ，一旦轨道焊接的不当或是变形 ，对工业门的整体运行都会带来不小的影响。今天Z6尊龙官方网站官网入口门业厂家小技术卖力人就来说说门轨道装置的要求。
What should we pay attention to in the track installation of industrial roller shutter? Track is the main part of industrial door switch operation. Once the track is welded improperly or deformed, it will have a great impact on the overall operation of industrial door. Today, the small technical director of Fuqiang door manufacturer said the requirements of door track installation.
一般情况下 ，工业卷帘门轨道接头可以做成直角或45度斜角接头 ，斜角接头能使门上的大轮子在接头处平稳过渡。
Generally, the rail joint of industrial rolling shutter door can be made into right angle joint or 45 degree bevel joint, and the bevel joint can make the big wheel on the door transition smoothly at the joint.
一般情况下 ，钢轨接缝为1-2mm ，如果是在寒区冬季施工或装置前温度低于终年使用温度2℃以上 ，装置卷帘门钢轨时应考虑温度缝 ，在单钢轨长度1m左右 ，应选用4-6mm。
Generally, the rail joint is 1-2mm. If it is constructed in winter in cold regions or the temperature before installation is more than 2 ℃ lower than the annual service temperature, the temperature joint should be considered when installing the rolling shutter rail. When the length of single rail is about 1m, 4-6mm should be selected.
另外 ，连接处两轨的横向错位和崎岖差应小于即是1mm。
In addition, the lateral dislocation and height difference of the two rails at the joint should be less than or equal to 1 mm.
同样截面上的工业卷帘门轨道面崎岖也会有误差 ，虽然这一误差也有相应的标准 ，即柱出距不小于1mm ，其它地方不小于15mm ，门式起重机、跨度大于4m的门式起重机和装卸桥不小于15mm。
The height of the track surface of the industrial roller shutter door on the same section will also have errors, although there are corresponding standards for this error, that is, the column spacing is not less than 1 mm, other places is not less than 15 mm, and the gantry crane, gantry crane with a span of more than 4 m and loading and unloading bridge are not less than 15 mm.
但在同一侧的工业门轨道面上 ，两柱之间的高度与相邻柱之间的高度之差不凌驾B/15mm ，但大不凌驾1mm。
However, on the same side of the industrial door track surface, the difference between the height between the two columns and the height between the adjacent columns is not more than B / 15mm, but not more than 1mm.
关于轨道跨度、轨道与承轨梁、轨道不直等方面的误差 ，应以轨道装置误差表为准 ，切勿对不可装置的误差表值进行盘算。
For the errors of track span, track and rail bearing beam, track straightness, etc., the track installation error table shall prevail, and the value of error table that cannot be installed shall not be calculated.
以上给各人介绍的是工业卷帘门的轨道装置需要注意的事项。希望各人阅读之后能增加对卷帘门的进一步认识 ，如果您想采购或者想了解更多知识 ，接待与我们进行联系。
The above is to introduce the track installation of industrial roller shutter door matters needing attention. I hope you can increase the further understanding of rolling shutter door after reading. If you want to purchase or want to know more, please contact us.
下一篇：浅谈对电动卷帘门进行结构调试要领 上一篇：电动卷帘门标准是什么？选购注意什么？
阅读/ Recommended reading
- 济南卷帘门的优点剖析 2024-12-16
- 济南卷帘门的装置指南：办法与注意事项 2024-12-11
- 济南卷帘门的维修保养：延长使用寿命的要害 2024-12-09
- 济南卷帘门：卷帘门�？仄魇Я槭笔允员疚牡囊彀桑� 2024-11-16
- 电动卷帘门的优势 2024-11-12
- 济南卷帘门：卷帘门�？仄魇Я樵趺窗�？ 2024-09-02
- 济南卷帘门厂：卷帘门卡主了怎么办 2024-08-28
- 济南电动卷帘门：电动卷闸门没电了怎么开? 2024-08-28
车库卷帘门故障及维修要领
2024-12-23
车库卷帘门在使用历程中可能会遇到种种故障 ，以下是一些常见的故障及其维修要领： Garage rolling shutter doors may encounter vario...
