Z6×ðÁú¹Ù·½ÍøÕ¾¹ÙÍøÈë¿Ú

Z6×ðÁú¹Ù·½ÍøÕ¾¹ÙÍøÈë¿ÚÍøÕ¾ ÔÚÏßÁôÑÔ ÁªÏµZ6×ðÁú¹Ù·½ÍøÕ¾¹ÙÍøÈë¿Ú

ЧÀÍ×ÉѯÈÈÏß

151 6888 2846

ÈÈÃÅÒªº¦´Ê£º Ë®¾§ÕÛµþÃÅ Ë®¾§¾íÁ±ÃÅ ¿¹·ç¾íÁ±ÃÅ

ÐÐÒµÐÂÎÅ

Ê×Ò³>>ÐÂÎÅ×ÊѶ>>ÐÐÒµÐÂÎÅÈçÄDZßÖõ綯¾íÁ±ÃŵشŸÐÓ¦¹ÊÕϵÄÎÊÌâ
ÁªÏµZ6×ðÁú¹Ù·½ÍøÕ¾¹ÙÍøÈë¿Ú
Z6×ðÁú¹Ù·½ÍøÕ¾¹ÙÍøÈë¿Ú

ÁªÏµÈË£ºÁÖ¾­Àí

µç»°£º151 6888 2846

ÓÊÏ䣺527800164@qq.com

µØµã£º¼ÃÄÏÊÐÀúÏÂÇø»¯Ï˳§Â·8ºÅ3ºÅÂ¥101ºÅ

ÈçÄDZßÖõ綯¾íÁ±ÃŵشŸÐÓ¦¹ÊÕϵÄÎÊÌâ

À´Ô´£º ÈÕÆÚ£º2022-06-30 Ðû²¼ÈË£º
µç¶¯¾íÁ±ÃÅÖ÷ҪװÖÃÔÚ¹¤³§¡¢¹¤Òµ³µ¼äµÈ³¡ºÏ £¬Èç¹ûºã¾ÃʹÓõĻ° £¬µØ´Å»·Õվɲ»¿ÉÖÆÖ¹µØ»á·ºÆð¹ÊÕÏ¡£½ÓÏÂÀ´ £¬³§¼Òdz̸ÈçÄDZßÖõ綯¾íÁ±ÃŵشŸÐÓ¦¹ÊÕϵÄÎÊÌâ¡£
Electric roller shutter doors are mainly installed in factories, industrial workshops and other places. If they are used for a long time, the geomagnetic ring will inevitably fail. Next, the manufacturer talks about how to deal with the geomagnetic induction fault of the electric roller shutter door.
¼ì²é½ÓÊÕÆ÷¹ÊÕÏ£º
Check for receiver failure:
×ÔÐпª¹Ø»òºìÉ«·¢¹â¶þ¼«¹Ü·¢¹âµÄ¼ì²â»·²»ÊÜ¿ØÖÆ¡£
The detection ring that switches on and off by itself or emits light from the red LED is not controlled.
¿ÉÄÜÔ­Òò£º½ÓµØÏß¹ÊÕÏ;µÚ¶þ¸ö¼ì²â»·×ÌÈÅ;ÓÐÎïÌåÔÚ¼ì²â»·ÖÐÒƶ¯;
Possible cause: ground wire fault; The second detection loop interferes; An object moves in the detection ring;
½â¾ö¼Æ»®£ºÓëÉÁ˸Áù´ÎµÄ½â¾ö¼Æ»®Ïàͬ¡£Èç¹û¿ª¹ØʱÊä³ö¼ÌµçÆ÷±¬·¢µç¸Ð £¬Ò²»áµ¼Ö¹ÊÕÏ¡£µ±ÕâÖÖÇé¿ö±¬·¢Ê± £¬±ØÐëʹÓÃ×ÌÈÅÒÖÖÆÆ÷½øÐб£»¤¡£
Solution: the same as the solution of flashing six times. If the output relay generates inductance when switching, it will also cause fault. When this happens, interference suppressors must be used for protection.
µç¶¯¾íÁ±ÃŵشÅÁ¬ÐøÉÁ˸¡£
The geomagnetic field of the electric roller shutter door flashes continuously.
¿ÉÄÜÔ­Òò£ºË«ÁÐÖ±²å»ò¿ª¹ØÉèÖò»ÕýÈ·;
Possible cause: dual inline or incorrect switch setting;
½â¾ö¼Æ»®£ºÇжϵçÔ´ £¬È¡ÏÂÍâ¿Ç £¬¸üÕýË«ÁÐÖ±²åʽ¿ª¹ØÉèÖá£
Solution: cut off the power supply, remove the housing, and correct the dip switch settings.
µç¶¯¾íÁ±ÃŵشÅÉÁ¶¯Á½´Î¡£
The magnetic field of the electric roller shutter door flashes twice.
¿ÉÄÜÔ­Òò£ºÌ½²â»·Ì«´ó»òÈÆȦ̫¶à(̽²â»·µç´ÅµÄÀíÏëÊý¾ÝÊÇ80~300uH);
Possible cause: the detection ring is too large or there are too many circles (the ideal electromagnetic data of the detection ring is 80~300uh);
½â¾ö¼Æ»®:¸ü»»¼ì²â»·»ò¼õÉÙÈÆ×éÊýÁ¿(ͨ³£3~5ȦÊǺÏÀíµÄ) £¬ÖØÖà £¬¸ü»»Ãô¸Ð¶È¿ª¹Ø £¬ÆÚ´ý3Ãë×óÓÒ £¬È»ºó½«Ãô¸Ð¶È¿ª¿Ú¸Ä»ØÔ­À´É趨µÄλÖá£ÈçÓÐÐëÒª £¬ÔÚ²Ù×÷Ç°ÇжϵçÔ´5Ãë¡£
Solution: replace the detection ring or reduce the number of windings (usually 3~5 turns is reasonable), reset, replace the sensitivity switch, wait about 3 seconds, and then change the sensitivity opening back to the original set position. If necessary, cut off the power supply for 5 seconds before operation.
¼ÃÄϵ綯¾íÁ±ÃÅ
µç¶¯¾íÁ±ÃŵشÅÉÁ¶¯ËĴΡ£
The magnetic field of the electric roller shutter door flashes four times.
¿ÉÄÜÔ­Òò£ºÌ½²â»·Ì«Ð¡»òÈÆȦÊýÌ«ÉÙ;
Possible causes: the detection ring is too small or the number of turns is too small;
½â¾ö¼Æ»®£ºÔö¼ÓµØ´ÅÏßµÄÈÆȦ×éÊý £¬È»ºóÖØÖá£
Solution: increase the number of winding groups of geomagnetic lines, and then reset.
µç¶¯¾íÁ±ÃŵشÅÉÁ¶¯Áù´Î¡£
The magnetic field of the electric roller shutter door flashes six times.
¿ÉÄÜÔ­Òò£º¼ì²â»·×ÌÈÅ¡¢½ÓµØÏß¹ÊÕÏ»ò¶Ì·¡£
Possible causes: detection ring interference, ground wire failure or short circuit.
½â¾ö¼Æ»®£ºÐÞ¸´¼ì²â»·¡£ÈçÓÐÐëÒª £¬¸ü»»¼ì²â»·»òÕÒµ½¼ì²â»·ËÄÖܵĽðÊôÎïÌå½øÐС£È»ºóÖØÖò¢¸ü¸ÄÃô¸Ð¿ª¹Ø £¬ÆÚ´ýÔ¼3Ãë £¬È»ºó½«Ãô¸Ð¿ª¿Ú¸ü¸ÄΪԭʼÉèÖÃλÖá£ÈçÓÐÐëÒª £¬ÔÚ²Ù×÷Ç°ÇжϵçÔ´5Ãë¡£
Solution: repair the detection ring. If necessary, replace the detection ring or find metal objects near the detection ring for removal. Then reset and change the sensitive switch, wait about 3 seconds, and then change the sensitive opening to the original setting position. If necessary, cut off the power supply for 5 seconds before operation.
µØ´Å¸ÐÓ¦¿ØÖƼÃÄϵ綯¾íÁ±ÃŵÄÊÂÇéÔ­ÀíÊÇͨ¹ý³µÁ¾µÄ½ðÊô²¿¼þ¸Ä±ä»·´«¸ÐÆ÷µÄÖµ £¬·¢ËÍÐźſØÖÆ¿ªÆôºÍ¹Ø±Õ¡£Òò´Ë £¬µØ´Å¸ÐӦͨ³£ÓÃÓÚ³µÁ¾ÐèÒª¾­³£Í¨¹ýµÄµØ·½¡£Ëü¾ßÓвÙ×÷¼òµ¥¡¢Ìá¸ßÊÂÇéЧÂÊ¡¢×°Öñ¾Ç®µÍ¡¢ÎÞÈËÔ±¼à¶½µÈÓŵã¡£
The working principle of Jinan electric roller shutter door controlled by geomagnetic induction is to change the value of the ring sensor through the metal parts of the vehicle and send signals to control the opening and closing. Therefore, geomagnetic induction is usually used where vehicles need to pass frequently. The utility model has the advantages of simple operation, improved work efficiency, low installation cost and no personnel supervision.
ÒÔÉϾÍÊÇÎÊÌâ½â´ðµÄÏà¹ØÄÚÈÝÁË £¬Ï£ÍûÄܹ»×ÊÖúµ½¸÷ÈË £¬Èç¶ÔÕâÒ»ÎÊÌ⻹±£´æÈκÎÒÉÎÊ £¬¶¼½Ó´ý¹Ø×¢ÎÒÃÇÍøÕ¾²¢×ÉѯÎÒÃǵÄÊÂÇéÈËÔ± £¬½«½ß³ÏΪÄúЧÀÍ¡£
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.

ÔĶÁ/ Recommended reading

¡¡¡¡³µ¿â¾íÁ±ÃÅÔÚʹÓÃÀú³ÌÖпÉÄÜ»áÓöµ½ÖÖÖÖ¹ÊÕÏ £¬ÒÔÏÂÊÇһЩ³£¼ûµÄ¹ÊÕϼ°ÆäάÐÞÒªÁ죺¡¡¡¡Garage rolling shutter doors may encounter vario...

¼ÃÄϾíÁ±ÃŵÄÓŵãÆÊÎö 2024-12-16
¼ÃÄϾíÁ±ÃŵÄ×°ÖÃÖ¸ÄÏ£º°ì·¨Óë×¢ÒâÊÂÏî 2024-12-11
¼ÃÄϾíÁ±ÃŵÄάÐÞ±£Ñø£ºÑÓ³¤Ê¹ÓÃÊÙÃüµÄÒªº¦ 2024-12-09
¼ÃÄϾíÁ±ÃÅ£º¾íÁ±ÃÅÒ£¿ØÆ÷ʧÁéʱÊÔÊÔ±¾ÎĵÄÒªÁì°É£¡ 2024-11-16
µç¶¯¾íÁ±ÃŵÄÓÅÊÆ 2024-11-12
¼ÃÄϾíÁ±ÃÅ£º¾íÁ±ÃÅÒ£¿ØÆ÷ʧÁéÔõô°ì£¿ 2024-09-02
¼ÃÄϾíÁ±Ãų§£º¾íÁ±ÃÅ¿¨Ö÷ÁËÔõô°ì 2024-08-28
¼ÃÄϵ綯¾íÁ±ÃÅ£ºµç¶¯¾íÕ¢ÃÅûµçÁËÔõô¿ª? 2024-08-28
ÍøÕ¾µØͼ